SIDEWAYS DP 2010 DOWNRIVER (MI) REGIONAL
NOTE: 8/19/10 - Slot.IT magnetic and spring suspension is now allowed.
DATE/TIME: Saturday September 25, 2010
A Racer Sideways Daytona Prototype regional race will be held at Downriver Speedway. Tech inspection will begin after conclusion of the Racer Resin regional race, which starts earlier that afternoon, click here for details. Race format will be 10 min. in each lane for a total of 40 min, subject to change by race host and organizer.
TRACK LOCATION:
Downriver Speedway
3918 Dix
Lincoln park MI 48148
Phone: 313-544-3374
Website: www.webstarts.com/downriverspeedway
Any shops, clubs or slotcar organizations interested in holding a regional event call Rich @ GT Slots: 267-250-1735
ELIGIBLE CARS:
Only Racer Sideways brand cars are allowed. Part no. SW01, SW01b, SW02, SW03, SW04, SW05, SW06, SW08, SW09 and as new cars are introduced they will become eligible. Click on this link for pictures of these cars.
THE BODY:
Bodies must not be modified or cut in any way-including wheel wells, EXCEPT: Since Racer has produced a car without the side panels, they can be removed altogether at the spoiler, or trimmed slightly along the bottom for clearance on the banking. Both spoiler and wing must still be in place. Cars must start each race with all parts intact (except for mirrors, wipers, antennas)
All cars must start with rear wing in place. Bodies can be painted. Simple paint is allowed but all cars must have numbers and look like race cars. Bodies must be attached to chassis using provided screws in stock location. If body screws are run loose, tape must be placed over holes in bottom of chassis. Windows must remain transparent. Due to an observed issue with some bodies clearing the spur gear (if using sidewinder configuration), a spacer/spacers of a maximum .030 width will be allowed on the rear body mount post to address this issue.
CHASSIS:
Racer chassis only w/Slot-it motor pods. NO TRACTION MAGNETS. Slot.IT magnetic and spring suspension is allowed, with any Slot.IT spring intended for their suspension. Inline & sidewinder motor pods only, standard or offset. Sanding edges of motor pods and chassis for float is legal. No modifications to axle mounts front or rear is permitted. Front axle ride height adjusting blocks must be in place if included in original model. Axle shims and/or stoppers are allowed.
WHEELS AND TIRES:
The stock front and rear wheels must be used. For front tires, original or any Slot.IT rubber tire may be used. For rear, any Slot-it S1 or S2 silicone tire except F1 is legal for the intended size wheel. Racers to supply their own tires. Tires may extend past body by no more than 1mm. Original inserts must be used but may be painted. No chemicals may be used on the tires.
GUIDE BLADES:
Only Slot-it guide blades are allowed. Any manufacture braid and wire can be used-must be attached to guide through Slot-it eyelets and may not be glued or soldered.
MOTOR:
Only Slot-it "Orange endbell" motor is legal (21,500 rpm @ 12volts), supplied by race host on race day. You will use your own Slot.IT pinion, as hand out motor will not have pinion installed, and motor must be returned to race host after conclusion of the race. Any Slot-it pinion may be used. No chemicals (ex: Voo Doo drops, etc. ) shall be added to the motor. Tape for holding the motor in place, if desired, will be supplied by host at the time of tech inspection. Only this tape will be allowed and it will be applied during tech under tech supervision. One (1) piece applied uniformally (an example will be shown on race day) shall be allowed for the sole purpose to hold the motor in place. Holes may be cut out of the tape to allow for cooling over the motor vent holes. No foreign substance(s) and/or objects shall be allowed to hold the tape down or to be placed under the tape as well. The race director will have the final determination if any questions or conflicts arise.
GEARING:
Any gear ratio is allowed using Slot-it gears
WEIGHT:
Weight may be added to the inside of the chassis (NO weight may be attached to the underside of the chassis.)
LIGHTING:
May be added (optional); If used must be Slot-it brand.
